Showing posts with label Pleasanton gas lines. Show all posts
Showing posts with label Pleasanton gas lines. Show all posts

Friday, May 24, 2013

East Bay Gas Lines - How to Seal a Gas Line on a Dryer

Seal the dryer gas line pipe threads with gas-rated tape or pipe thread compound.




Once you get your new gas dryer home, you must safely connect it to the gas line. A dryer isn't hard to connect to a gas line, but if you don't do it correctly, it could be dangerous for your family and your home. Improperly connected gas lines to dryers, for instance, allow gas to leak inside the home. Gas buildup can result in an explosion when ignited, and the fumes are not safe to breathe. After connecting your gas line to your dryer, conduct an easy test to ensure it has a good seal and does not leak.

1 Measure the distance from the gas line to where the dryer will be installed. Use the measurement to size the flexible gas hose connection.

2 Match the flexible hose connection to the gas fitting in the house. Gas lines in newer homes are typically made from steel or black iron. Choose the flexible gas hose to match the gas line. For instance, for a steel or iron pipe, use a steel flexible gas line.

3 Clean the threads on the gas pipe that extends from the wall. Gently run the wire brush around the end of the pipe to remove any burrs or debris on the pipe threads. Wipe the threads with a clean soft rag.

4 Apply the gas-rated Teflon tape or pipe thread compound to the threaded end of the gas line in a clockwise direction.

5 Thread the flexible gas hose fitting onto the threads. Then tighten the fitting using the pipe wrench, but don't over tighten.

6 Repeat the thread-sealing procedure for the gas line that comes from the dryer.

7 Fill the water bottle halfway with a 1-to-1 mixture of detergent and water.

8 Turn the gas valve on. The gas valve is on the gas line that extends from the wall. When it is on, the handle is in line with the gas line. When it is off, it is perpendicular to the line.

9 Spray the connection on the gas line that extends from the wall where the flexible gas hose connects to it with the detergent and water mixture. Watch for bubbles to form. If no bubbles form, there are no leaks.

10 Move to the gas connection on the dryer side and repeat the procedure for checking for leaks. If no bubbles form, the gas dryer line is sealed between the gas line and the gas dryer.

Tip
Double-check the pipe tape or pipe thread compound package to ensure each is rated to seal gas lines.
Avoid purchasing a flexible hose that is too short or too long. You don't want the line to kink, twist or compress itself.

Use a soft rag that doesn't leave any fibers on the pipe threads, as these fibers could compromise the seal.
Avoid over tightening the fittings, as you don't want to break them. For homes fitted with copper flare fittings, use the detergent mixture to check all the connections for leaks before using your dryer.

Warning
If you don't have experience or are concerned with doing this project yourself, contact East Bay Gas Lines to hook up your dryer for you. 


by Laurie Reeves, Demand Media

http://www.eastbaygaslines.com

Friday, May 3, 2013

East Bay Gas Lines - Home Inspections that Failed


This potato is being used as a cap for an active gas line. Note that it did try to sprout.

Dan Howard


a potato with roots sprouting out of it used as a gas line cap

Photo  Dan Howard




This homeowner decided he would fix his dripping temperature pressure relief valve one way or another. A simple replacement would have probably taken as long as it took to get this rigged solution to work.

Brian Mishler




a TPR valve tightened with a pair of locking pliers that are held in place with electrical tape
photo - Brian Mishler




This is an interesting example of someone who does not think gas combined with electric can hurt you.

Michael Legatt




gas and electrical lines all mixed up together
photo - Michael Legatt






source: http://www.thisoldhouse.com/toh/photos/0,,20206857_20470632,00.html

http://www.eastbaygaslines.com

Friday, April 19, 2013

East Bay Gas Lines - Furnace & gas line safety tips





A gas leak refers to the seeping of natural gas, frequently through a pipe, which can endanger the lives of those in the area. While the fumes may cause health problems, the larger problem is the potential for an explosion because natural gas is highly flammable.
1)      Have your furnace and gas lines checked every spring and fall.
2)      If you ever smell natural gas (it smells like rotten eggs) open the windows and call the gas company immediately (don’t assess it yourself).
3)      You may hear unusual noises coming from your gas lines.
4)      Don’t turn on lights or use a cell phone.
5)      Don’t ignite or light a lighter, smoke etc.
6)      Clear out—immediately—and warn others to do the same.
7)      Do not start a car or any nearby machinery.
8)      If you’re in a building with elevators—don’t use the elevator.
9)      Do not try to manage the situation on your own.
10)   From a safe place, call the gas company and 911.
If you have not had your furnace checkup during the fall, call us today to schedule one

by Larry Howald

Friday, April 12, 2013

East Bay Gas Lines Danville - Gas Grill Maintenance


Wolf Grill
Photo: Courtesy of Wolf Appliances


Nothing announces the arrival of summer like firing up the grill. Unfortunately, nothing sours a summer party faster than a grill that won't light, smokes too much, or cooks unevenly. Grease, marinades, and sauces wreak havoc on gas burners, while charcoal grills suffer the corrosive properties of charcoal.

Grills of all kinds, from simple kettles to stainless steel restaurant-grade infrared grills, require maintenance to ensure that they perform and last. "At least twice a year you need to pull the grill apart to get inside and take a closer look at it," says Derrick Riches, barbecue and grilling guide for About.com. A thorough cleaning ensures that the burners fire properly, heat distributes evenly, and the grill is safe. Regular maintenance also allows you to catch problems like rust early on. Here is a This Old House primer on keeping your grill in shape.

Inspect the Chassis: Grills with welded joints or connections with pop rivets can rust. Scrub rust off with a stiff wire brush or coarse steel wool, apply a rust-inhibiting primer, and paint the grill's exterior with rust-resistant metal paint. Keep fasteners tight to ensure the base is stable and safe. Replace damaged grill appendages, like wheels, handles, or any other part of your grill, by contacting the manufacturer. You can also refer to the 
CLA Grills and Service website, or the Appliance Factory Parts website. Use dish soap or a mild detergent to clean cast aluminum grills, and Simple Green all-purpose, biodegradable cleaner for stainless steel ones. 

Clean the Burners: Riches stresses that cleaning burners keeps the unit working at its best. Burner ports can fill with grease and close up, leading to hot and cold spots on the grill. While the unit is cold, use a stainless steel wire brush or flexible pipe cleaner to remove the gunk from a traditional gas burner. The flames should be distributed evenly throughout the burner after a good cleaning. Brush off any ash that accumulates on infrared grills, and be sure to keep the glass clean. Infrared grill manufacturers suggest using 
Bar Keepers Friend, a non-abrasive cleaner, to remove any deposits. Running the grill for 10 minutes on high after cooking also helps keep the ports free of build up.
Flame Color: There are a couple of reasons gas flames turn from their normal blue with yellow tips to completely yellow. The most common is inadequate gas pressure from the tank. Since propane expands at freezing temperatures, the pressure bladder in the regulator (a round disk attached to the gas line) can freeze into place and limit the flow of gas to the burner. If you have a yellow flame, try this remedy: First, turn the tank off and turn off the grill's control valves. Next, disconnect the tank, then open and close the control valves. Finally, reconnect the tank and slowly turn the gas back on to check the flame's color. Another cause of yellow flame is pressurized propane that, over time, can force the burner ports to widen. As a result, too much gas escapes. Riches recommends inspecting the burners and replacing them if they are misshapen or cracked. Once the burners are cleaned, light the grill to ensure that all flames are blue and similar in height.

Grease traps: Grill grease traps are typically trays or disposable aluminum cups beneath the firebox that collect fat. Keep these traps clean and drained because large pools of grease can ignite. Burners combined with a grease fire will exceed the maximum amount of heat the grill can handle.

Hoses: Replacing a worn or damaged fuel line is an easy task once you locate the problem. Manufacturers suggest coating everything—from the tank, to the venturi tubes, which connect the control valve to the burner—with soapy water. For a neat job, Riches uses a basting brush to apply the soap solution. Then, turn the grill on. Any bubbles that appear on coated areas indicate escaping gas, which can be fixed by replacing the hose or O-ring. The gap in the venturi tubes mixes gas with air enroute to the burner and can easily clog with debris or insects. Riches recommends wrapping the tubes with aluminum screen to let air in and keep bugs out.

Between the Burner and Grate: Sometimes called the radiant or flavorizer bar, this part of the grill evenly distributes heat to the grate above and produces smoke when food drippings seep down. "Most of the wear is in the flavorizer bars, because they see the most heat and grease," says Brooke Jones of Weber Grills. Brush off grease and debris from the metal plates because they can trap moisture and cause rusting. Replace lava rocks or ceramic briquettes if they give off a rancid flavor.

Grill Covers: Keeping a grill protected from the elements is the easiest way to preserve it. Covers should have a cloth inner lining to draw moisture away from the metal. A simple plastic sheet holds moisture in, creating a humid environment around the grill, which can lead to rusting. Use a canvas, cloth, or vinyl cover that fits the grill appropriately. Keep in mind that UV rays beak down cheaper, generic covers.
source: http://www.thisoldhouse.com/toh/article/0,,1638829,00.html
by Sal Vaglica

http://www.eastbaygaslines.com

Friday, March 22, 2013

East Bay Gas Lines - Gas Appliance Safety





  

When lighting any match-lit burners or ovens, always light the match before turning on the gas. If the flame goes out, turn off the burner and let the gas disperse before relighting.

Clean away any grease, oil or debris from the area around burners to help prevent fires.

Never use water to put out a grease fire. Use baking soda, or if a fire is in a pan, smother the flames with a lid. A fire extinguisher in the kitchen is also recommended.

Move any flammable objects — towels, curtains, calendars — away from range burners and other hot surfaces.

 
Ovens

Never use your oven for domestic heating. This misuse of your oven puts you at risk of burns from hot surfaces and shortens the life of oven parts and controls. Use only heaters that are designed for domestic heating and follow the manufacturer's operating instructions.

 

Make sure your water heater issecurely anchored to a wall. This will help prevent the heater from shifting and possibly falling in an earthquake.

If your water heater is on an elevated platform, make sure the platform is sturdy enough to withstand the weight of the water heater and movement during an earthquake.

A temperature of 120 degrees F is adequate for most household uses with minimal danger of scalding and maximum energy efficiency. Dishwashers require a temperature of 140 degrees F for proper disinfection and cleaning. Most dishwashers preheat the water to the proper temperature; if not, lowering the water-heating temperature is not recommended

Do not store flammable materials — mops, brooms, laundry, newspapers — near your water heater.

Do not store combustible materials — paints, solvents, gasoline — in the same room or near your water heater.

  

Your furnace should be serviced once a year to help maximize its life and performance. Follow the instructions in the owner's manual, or call a qualified professional.

Have your furnace checked for fire hazards such as a damaged firebox and any dislodged, clogged, rusted or damaged vents.

Clean or replace your filter regularly, or after each month of heavy usage.

Replace the blower door cover after checking your filter.

Securely fasten the door that covers the pilot light and burner area.

Do not store combustible materials — paints, solvents, gasoline — in the same room or near your furnace.

Do not store flammable materials mops, brooms, laundry, newspapers — near your furnace.

Air-supply vents must be clear of obstructions. Furnaces need a constant supply of fresh air to run efficiently and safely.

Kerosene heaters or other unvented heaters are not recommended and should only be used in well-ventilated rooms. Always operate your heater according to the manufacturer's instructions.

All Gas Appliances

Do not store flammable materials — mops, brooms, laundry, newspapers — near gas appliances.

Do not store combustible materials — paints, solvents, gasoline — in the same room or near your appliances.

Make sure a flexible gas line connection is installed connecting the gas houseline (the gas pipe connecting your appliances to the gas meter) to the appliance to reduce the likelihood of damage if movement should occur.

You should have an appliance gas shutoff valve installed at each gas appliance that lets you turn off the gas to that appliance only if there is a gas leak, or if the appliance needs to be replaced or serviced.
 

 

Friday, March 8, 2013

East Bay Gas Lines - Danville - How do I Know What Size Generator to Buy for My House?






A backup generator can provide power in the event of an outage for essential appliances such as refrigerators, freezers, sump and lift pumps and a few lights. Estimating the size of the generator required means adding up the total number of watts used by each appliance you intend to provide power in the event of an outage. This information is available on the appliance nameplates or in the documentation supplied with each appliance. The more appliances you include, the more that can be powered, but the cost increases as the size of the generator goes up.

1 Make a list of the appliances you wish to power during an outage. Include refrigerators, freezers, furnace, and electric range, along with well, sump, lift or ejector pumps. Include the number of watts each appliance requires for starting and running. Consult the appliance documentation or nameplate for this information, which is expressed as watts, kilowatts or volt-amps. Calculate power requirements by multiplying amps by voltage for appliances that do not list watts, kilowatts or volt-amps.

2 Determine starting power requirements for appliances with motors that do not list the starting power needed, such as refrigerators, air conditioners, washers and dryers. Contact the manufacturer of these appliances or consult a chart that gives average requirements for these appliances.

3 Total the running power requirements for appliances which do not have different starting and running loads, such as incandescent lights, water heaters and toasters. Total the starting power requirements for other appliances with motors, such as pumps and refrigerators. Add the two totals together for the total power required.

4 Choose between 240-volt and 120-volt generators; 240-volt generators will run electric stoves, electric baseboard heaters, electric dryers, central air conditioning units and dishwashers. Select a model the provides both the voltage and the total power requirements needed to run the appliances you selected to have operational during a power outage.
 
 

Friday, February 15, 2013

East Bay Gas Lines - Water Heater Safety 100








water heating
 photo by Eddie Berman

 

Your gas water heater might look benign, but if it's improperly installed or maintained it's a potential ballistic missile that could erupt with enough force to lift your house off its foundation. Every year a few water heaters explode with devastating results. To make sure yours is safe, follow these simple steps:

Remove paper, accumulated dust or other combustibles from the heater enclosure.

Extinguish the pilot light before using flammable liquids or setting off aerosol bug bombs near the unit. Never store combustibles close by.

If the device is in the garage, raise it so the pilot light is 18 in. above the floor. This can help prevent ignition of gasoline vapors that collect near the floor.

Inspect the flue for breaks or gaps that could leak deadly exhaust gas. (This is a good practice to do on other gas appliances.)

Ask your service technician to check the temperature pressure-relief valve, a faucet-like device mounted on the top or side of the heater. Excessively high temperature or pressure causes this valve to open, relieving pressure and preventing a steam explosion.

Consider installing an automatic gas-shutoff valve (below) that stops the flow of gas if the ground moves or if gas flow increases dramatically. The valve, which costs around $300, prevents fires when a gas line breaks due to flood, earthquake or other disaster. Some utility companies will install one and let you pay it off monthly.
by Leland Stone
 
 

Friday, February 8, 2013

East Bay Gas Line Repair - Gas Stove Burner Safety - East Bay Gas Lines Danville






Gas Stove Burner Safety
Gas Stove Burner Safety
 

Gas stoves allow for precise heat control while cooking. In some areas of the country, gas appliances are more economical to operate. Take precautions to operate a gas stove safely. Improper operation could lead to fires, burns or carbon monoxide poisoning.

Carbon Monoxide

Any gas appliance can be a source of carbon monoxide, a dangerous gas that deprives the body of oxygen, resulting in serious injury or death. Don't use a gas stove as a source of heat, as this increases the likelihood of carbon monoxide poisoning. Make sure the stove is vented to the outside and the vent it not blocked. Install a carbon monoxide detector in homes where gas appliances, including gas stoves, are being used.


Cooking

The flame beneath a pot on the stove shouldn't extend past the sides of the pot. Use the right size pot for the burner and adjust the flame so that it doesn't flare up around the pot. Don't allow food to boil over. This could put out the flame, while still leaving the gas on, which increases the potential for a fire or explosion. Food that boils over could also block holes in the gas burner and lead to uneven cooking or difficulty lighting the burner. Don't line the stove burners with foil, as this could inhibit air flow to the burners.

Fire Hazards

Don't leave flammable materials such as dish towels near the stove. Don't set boxes, plastic dishes or items other than cooking pots on top of stove burners. Make sure you turn burners completely off after use. Don't allow pots to boil dry on the stove.

 Troubleshooting

If your stove won't light, first check that the holes around the burner aren't blocked with food or other debris. You can clean these with a piece of wire or a toothpick, though be careful not to break the toothpick off in the hole. On some stoves, the burner cover must be lined up correctly in order for the stove to light, so check this also. If the electronic igniter clicks, but doesn't work, try lighting the stove with a match. This will help burn off debris blocking the igniter.

Gas Leaks

If you smell gas, first make sure all the burners are turned completely off. If they are and you still smell gas, get out of the house and go to another location and call the gas company.

Even if you don't smell gas, if you suffer from persistent headaches, fatigue, nausea, dizziness or flu-like symptoms---especially if you feel better away from home---you may be suffering from carbon monoxide poisoning. Leave the house and contact the gas company to inspect the stove.

source: http://www.livestrong.com/article/138662-gas-stove-burner-safety/
by Cynthia Myers


www.eastbaygaslines.com

Friday, January 18, 2013

East Bay Gas Lines - Water Heater Safety is often taken for Granted





Water heaters are often taken for granted. They sit in our garage or utility closet and perform their assigned duty day in and day out. If installed correctly they will operate with little fuss for many years. Most of us rarely give the water heater a second thought, but they have a life cycle just like every other component or appliance in your house.

At the very minimum you should take a careful look at your water heater at least once a year. One of the most common points of failure is at the top of your water heater where it connects to the house plumbing. If the water heater was not installed with proper dielectric connectors, you will get corrosion where the copper plumbing meets the steel tank. Corrosion at water heater this area is often difficult to see. A tank can be five feet tall and when properly installed on an 18 inch platform, the top of the tank is 6-1/2 feet off the ground. This area can easily be over looked.

If you see heavy rust in this area, your tank is ready to leak. remember that your plumbing system is under pressure 24 hours a day. It doesn’t take much corrosion to eat through the plumbing. Even a small leak can flood your house. Even if your water heater is in your garage, a leak can find its way to the interior of your house. Water often sprays out of a small breach in the plumbing with such force that it quickly destroys the drywall, and gets inside the walls, and into your house. Just a small amount of water can destroy wood flooring, baseboards, carpeting, furniture, or personal items that are sitting on the floor.

Rusty water heater piping can cause leaks

In addition to looking for corrosion, look for evidence of soot at the exterior of the tank. This can be found around the burner compartment cover at the bottom of your water heater. If you are comfortable doing so, open the cover and look inside the compartment. Be careful of hot parts. If the water heater is on the inner cover will be hot. Once you remove the inner cover look for scale and rust inside the burner compartment. Old, damaged parts in the burner compartment can cause the water heater to remain on and over heat. This is a major cause of house fires.

Proper venting is critical to the safe operation of a water heater. Check the flue. It should be properly aligned with the top of the tank. And the sections of the flue should be well seated. Do not use duct tape on the flue. It can catch fire. An improperly installed flue can allow Carbon Monoxide to leak into your living space.
A general rule of thumb is to proactively replace your water heater when it has reached the end of its warranty period. That usually means that if your water heater is more than 7 years old, it should be replaced before you have problems with it. The price of a water heater is usually less than your insurance deductible. When in doubt, have your water heater inspected by a licensed plumber. It does not cost much and could save your family from injury, and you home from damage.

source: http://sdinspections.com/tag/water-heater-safety

http://www.eastbaygaslines.com

Friday, January 11, 2013

East Bay Gas Lines - Upgrade and Save Energy with Fireplace Inserts


Upgrade and Save Energy with Fireplace Inserts

Adding an insert is a smart investment that's pure win-win—it'll keep you warm and slash your heating bills all at once



According to the National Association of Home Builders, fireplaces rank among the top three features desired by new homebuyers. Unfortunately, fireplaces are also major air gaps—they can send up to 8 percent of valuable furnace-heated air flying out the chimney, making them really fun to look at but inefficient as heating sources. Here's the good news: You can transform your firebox into an efficient room heater by adding an insert.

An insert, installed by a factory-trained professional (to ensure proper venting and best efficiency results), will draft-proof an open fireplace while the unit's shell keeps heat in the room and away from the masonry. The cost can can set you back about $2,000 to $4,000 (pro install included), depending on the state of your existing chimney (does it need relining?) and the model you select. But this investment pays for itself by slashing those monthly heating bills. 

 
Upgrade and Save Energy with Fireplace Inserts
Adding an insert is a smart investment that's pure win-win—it'll keep you warm and slash your heating bills all at once
Pacific Energy Super Insert

 pacific energy fireplace insert

This redesign of the popular wood-burning "Pacific" model now has a more refined look and can fit into smaller fireplace openings. The unit features an airwash system to keep its heat-conducting ceramic glass clear and one-touch adjustable temperature control. Variable speed blower included, to easily heat up to 2,000 square feet. Available in one- or two-door styles with gold, nickel, or metallic trim.

 

Lennox Ravenna Elite Series Gas Insert
lennox gas fireplace insert
 

This unit is will fit most factory-built and masonry fireplaces and features a realistic dancing flame over a log set cast from real wood. Blower delivers heating for up to 2,000 square feet via optional wireless remote thermostat control. Available in a variety of face options and inset designs. 

 

Enviro EF3Bi Pellet Insert

 Enviro Pellet fireplace insert

This model delivers the most heat in the Enviro pellet insert line of product, quickly heating up to 1,800 square feet. It features an ignitor, easy-clean ports, and a three-piece glass bay door for optimal flame-watching. Feed the hopper with renewable recycled wood wastes, dried corn, or another readily available economical source for your area.

 

QuadraFire Mt. Vernon Pellet Insert

 quadrafire pellet fireplace insert

This extra-large unit comes standard with comfort-quiet blowers to heat up to 3,800 square feet. Like other pellet models, it runs on biofuels, including wood pellets, corn, sunflower seeds, and wheat. Other features include a firepot auto-clean system, programmable thermostat wall control, and auto lighting and operation programs for different fuels.
 
source - This Old House online
by Tabitha Sukhai
 

Friday, January 4, 2013

East Bay Gas Lines Danville - Water Heater Safety 101


Water Heater Safety 101

Your water heater may look benigh, but if improperly handled, it could erupt


water heating
photo by Eddie Berman


Your gas water heater might look benign, but if it's improperly installed or maintained it's a potential ballistic missile that could erupt with enough force to lift your house off its foundation. Every year a few water heaters explode with devastating results. To make sure yours is safe, follow these simple steps:

Remove paper, accumulated dust or other combustibles from the heater enclosure.

Extinguish the pilot light before using flammable liquids or setting off aerosol bug bombs near the unit. Never store combustibles close by.

If the device is in the garage, raise it so the pilot light is 18 in. above the floor. This can help prevent ignition of gasoline vapors that collect near the floor.

Inspect the flue for breaks or gaps that could leak deadly exhaust gas. (This is a good practice to do on other gas appliances.)

Ask your service technician to check the temperature pressure-relief valve, a faucet-like device mounted on the top or side of the heater. Excessively high temperature or pressure causes this valve to open, relieving pressure and preventing a steam explosion.

Consider installing an automatic gas-shutoff valve (below) that stops the flow of gas if the ground moves or if gas flow increases dramatically. The valve, which costs around $300, prevents fires when a gas line breaks due to flood, earthquake or other disaster. Some utility companies will install one and let you pay it off monthly.
by Leland Stone
 
 

Friday, December 28, 2012

East Bay Gas Lines Danville - Making gas connections to steel gas pipe



 
Make connections to steel gas pipe

Older houses often have threaded steel gas pipe. If your old appliance is connected with a steel pipe and you're installing a new appliance, buy a gas appliance connecting kit and replace the steel pipe with the flexible stainless steel tube. But remember, you can't connect the flare fitting on the flexible gas line directly to a steel pipe thread. You have to install the flare fitting that's included with the kit.

Also replace old-style gas valves (photo below) with modern ball valves that are labeled for use with gas. Before you replace an old valve, you'll have to find and turn off the main gas valve to the house. It's usually located near where the gas line enters the house. When you turn the gas back on, remember to check all your gas appliances to see if they have pilot lights that need relighting.

The photo shows how to use common plumbing parts to join a new ball valve and a flexible stainless steel connector to steel pipe. Coat all threaded pipe connections with pipe thread compound before assembly. The valve shown has 1/2-in. female pipe threads on both sides. If necessary, use a bushing to reduce the existing 3/4-in. female pipe thread to 1/2 in. Use a 90-degree elbow at the stove to avoid kinking the gas tubing when you push the stove against the wall.

 

Steel pipe gas connections

Proper Connections to Steel Pipe

Use the fittings shown for safe connections.

 

Old style gas valve


Old-style gas valves can leak. Replace them with approved ball valves.
 
 

Friday, December 21, 2012

East Bay Gas Lines - Most Expensive Grilling Products Ever



Most Expensive Grilling Products Ever

Whether it's a stainless steel free-stander the size of a Ford F-150, or a complete outdoor kitchen with the beer bar built right in, some men measure each other's mettle simply by the quality of their backyard equipment

Friday, December 14, 2012

East Bay Gas Lines Danville - All About Gas Fireplaces



a Craftsman-style gas fireplace from Majestic Products
 

 

There's only one thing better than a roaring fire on a wintry night: a roaring fire that needs no tending, requires minimal cleanup, and doesn't leave the rest of the house freezing cold. That's what you get with today's gas fireplaces. Long gone are the anemic blue flames and unconvincing "logs." Modern versions burn much more realistically, with glowing red embers and tall orange-yellow flames that dance and flicker around ceramic-fiber logs molded from the real thing.

Gas fireplaces come in three types: inserts, for folks who want to retrofit a wood-burning firebox with something more convenient and efficient; built-ins, for those who want a fireplace where there isn't one now; and log sets, basic burners that sit in existing, open fireplaces. Both inserts and built-in fireplaces are reliable heat producers, filling your room with a mix of warm air and radiant heat. Log sets are usually more for looks than warmth. With each type, you have a choice between models that vent the flames' fumes outside or vent-free versions that discharge all their heat, and exhaust, into the house. 


How much do they cost?
Expect to pay $2,000 to $5,000 (including installation) for a heat-producing insert or built-in fireplace. Decorative log sets run about $400 to $1,000.

Natural gas or propane?
Gas fireplaces can burn either type. Natural gas is less expensive and produces about 5 percent more heat. Choose propane where natural gas isn't available.

DIY or hire a pro?
For the safest, most efficient, and best-looking installation, leave the work to a local National Fireplace Institute-certified technician.

How much care?
For about $150, have your certified technician come once a year to clean and adjust the burner, ensuring that you have realistic, soot-free flames.

How many Btus?
A gas fireplace's heat output, in Btus, should match your room size, climate, and your house's insulation level.

Why Choose Gas?
two women pouring juice at a table next to a gas fireplace
 

Wood-burning fireplaces provide great ambience, but they can't beat the easy, no-fuss efficiency of gas.

• You don't have to split, stack, season, or haul logs.
• There are no ashes to bag, no smoky smells, no chimney to clean.
• You can start, adjust, and snuff out fires with the touch of a remote control.
• The fire needs no tending and won't die out from neglect.
• A wall thermostat can control the flame size—and therefore heat output—to maintain a specific temperature setting in the room.
• The fixed glass panels covering direct-vent fireboxes ensure that the furnace- or boiler-heated air in the rest of the house doesn't escape up the flue, as it does with a wood fire.
• You can get as much as 75 to 99 percent of a fuel's energy back as heat, instead of the 10 to 30 percent for wood fires.
• Gas fireplaces can go almost anywhere—in an upstairs bathroom, in a basement, or outdoors—without needing a chimney.

What to look for-
woman lying on a thick shag rug with a laptop in front of a gas fireplace

These upgrades enhance a fireplace's convenience, comfort, and good looks.

1. Variable-flame height adjustment. Allows you to dial in just the amount of heat you need, from a whisper of a flame to a roaring fire. (The best units adjust down to 30 percent of full output).

2. Wall-thermostat control. Automatically adjusts the fireplace's heat output to the temperature that you set manually or with a handheld remote.

3. Electronic ignition. Eliminates the need for a pilot light, saving up to $10 a month in fuel.

4. LED accent lighting. Adds a realistic flickering effect inside the firebox.

5. Battery backup. Ensures the fireplace will light during a power outage.

6. Built-in fan. Pulls indoor air into the space behind the firebox and pumps hot air out, heating a room in a hurry.

How Much Fire Power Do You Need?

 map of USA showing BTU zones and equation for figuring out BTUs needed

Gas fireplaces have a wide range of heat output, from about 7,000 to 60,000 Btus. Use this formula to determine which models generate enough heat to warm your room. The formula assumes that your house is well insulated and has tight windows, and that you like the temperature set at 72 degrees F.

By JOSH GARSKOFTHIS OLD HOUSE MAGAZINE

Source: http://www.thisoldhouse.com/toh/photos/0,,20431996_20859244,00.html

Friday, December 7, 2012

East Bay Gas Lines Danville - Winter Gas Saving Tips






A few small changes can add up to a whole lot of savings. Use PGE’s online Progress Tracker to keep track of your gas usage. Reduce your gas usage throughout December and January and you could get up to a 20% bonus credit on your PG&E bill.

See below for a whole range of ways to lower your gas costs in the “tips” section below.

·         Lower the thermostat by 1° F (if it’s set between 60° and 70°F) and you can save as much as 5 % on heating costs.

·         In the winter, open your window coverings on sunny days to help warm the rooms.

·         Save on heating costs. Keeping your thermostat set at 68º F during the daytime and 55º F at night can reduce your heating costs by up to 20%.

·         Dishwashers with booster heaters will let you lower the water temperature on your water heater, resulting in energy savings.

·         Wrap older water heaters with an insulating jacket to minimize excess heat loss. And, don’t forget to leave the air intake vent uncovered when insulating a gas water heater. Savings of up to 10% can be achieved on water heating costs.

·         In the winter, reverse your ceiling fan motor to produce an updraft that forces warm air near the ceiling down into your working space.

·         Properly sealing and insulating your business can save you up to 20% on heating costs

·         Replacing your old windows with high-efficiency ENERGY STAR® windows can reduce your heating and cooling costs by up to 15%

·         Have a licensed HVAC contractor check your central heating/cooling duct system for leaks. Sealing and insulating ducts can improve the efficiency of your heating system by as much as 20% — and sometimes much more.

·         Replace your pre-1977 gas furnace (probably 50-60 percent efficient) with the most efficient model and you could cut your natural gas use by up to 33%.


source: http://www.pge.com/myhome/saveenergymoney/wintersavings/

Friday, November 30, 2012

Gas Line Work East Bay - How to Read Your Gas Meter - East Bay Gas Lines Danville

 How to read your gas meter

Your gas meter tells us how much gas you’ve used and helps us to give you accurate energy bills. Reading your gas meter is easy once you know how. Use our simple instructions to find out how your gas meter works.

Imperial meters

If your meter measures in cubic feet (ft3) the display panel will show four digits before the decimal point.

Metric meter

If your meter measures in cubic metres (m3) the display panel will show five digits before the decimal point.

Digital meter 



If you have a digital meter please remember the following points when you take a reading:
Record main digits only – main digits will be shown in black on a white background, or in white on a black background
Ignore red digits
Ignore digits inside a red border
Ignore printed zeros – 0
Ignore any numbers after a decimal point

For example, the reading for the digital meter shown below should be recorded as 6653.

Dial meter


If you have a dial meter, please remember the following points when you take a reading:
Adjacent dials rotate in opposite directions
Ignore dials marked ‘100 per rev’ and the large dial
Ignore red dials
Read the other dials from left to right; write down the number that the hand has passed
If the pointer falls between two figures, write down the lower figure. If the pointer falls between 9 and 0, write down 9

For example, the reading for the dial meter shown above should be recorded as 6653.

source: http://www.edfenergy.com/products-services/for-your-home/my-account/how-to-read-your-gas-meter.shtml

http://www.eastbaygaslines.com

Friday, November 23, 2012

East Bay Gas Lines - Natural Gas: Earth and Sky Friendly




Natural Gas: Earth and Sky Friendly

Natural gas – the ultimate “alternative” fuel of the future? Yes, the same natural gas first commercially used in the United States in western New York in the early 19th century. When it comes to dealing with issues surrounding pollution and the environment, carbon management and energy security, natural gas is part of the solution, not part of the problem. Yes, natural gas is a “fossil fuel.” But natural gas is far more environmentally attractive than oil, coal, and electricity produced with fossil fuels. Of the major sources of energy in the United States, natural gas is the cleanest, most efficient, cost effective, and abundant, producing less pollution and fewer greenhouse gasses than its counterparts.



Gas=Environmental Benefit: Fewer Greenhouse Gasses chart

Source: Energy Information Administration: Fuel and Energy Codes and Emission Coefficients

Fewer Greenhouse Gas Emissions:

The primary byproducts of burning natural gas are carbon dioxide and water. But natural gas produces LESS carbon dioxide than other commonly used energy sources. According to the federal Energy Information Administration (EIA), natural gas emits 45 percent LESS CO2 than electricity and nearly 30 percent LESS CO2 than fuel oil. In fact, the U.S. is now a world leader in carbon reductions, having reduced carbon emissions by 7.7% since 2006, the equivalent of removing 84 million cars from the road. As acknowledged by the chief economist for the International Energy Agency, the replacement of coal by shale gas was a key factor driving the carbon emission reductions in the U.S.

Cleaner:

Natural gas generates less sulfur dioxide (a cause of acid rain), less nitrogen oxides (that can produce smog) and less particulate matter than oil or coal, which is primarily used for electric generation. The cleanliness of gas means that not only does it produce less pollution, but also environmental controls on gas equipment are usually much less expensive than for other fuels. Additionally, technological progress allows cleaner energy production today than in the past. Natural gas use means cleaner air whether used for home space heating, water heating, cooking, clothes drying, and in the case of natural gas vehicles, cars, trucks, buses, and commercial and industrial processes.

Pounds of Air Pollutants per Billion Btus of Energy

POLLUTANTNATURAL GASOILCOAL
Carbon Dioxide117,000164,000208,000
Carbon Monoxide4033208
Nitrogen Oxides92448457
Sulfur Dioxide11,1222,591
Particulates7842,744
Mercury0.00000.00070.016
Source: Energy Information Administration

More Efficient:

Natural gas appliances are more energy efficient than their electric counterparts, and natural gas users thus conserve energy resources and reduce greenhouse gas emissions. According to the American Gas Association (AGA), while the number of natural gas residential customers increased 71 percent since 1970, the average customer today uses 39 percent less natural gas than they did 38 years ago. By using energy wisely, weatherizing homes, using energy-efficient appliances and installing programmable thermostats, customers reduce greenhouse gas emissions.



Efficiency graphic: Electricity vs. Natural Gas

source: http://www.nationalfuelgas.com/natural_gas_environment.aspx


http://www.eastbaygaslines.com